Collets / Chuck

Quick change collet kit The quick change collet allows you to fit the following collet diameters: Ø 0.8mm Ø 1.6mm Ø 2.4mm Ø 3.2mm Make sure to tighten the collet nut with a collet wrench.....

Replacement collet - Ø 0.8mm The collet is used to hold mini rotary accessories with a shank diameter of Ø 0.8mm....

Replacement collet - Ø 1.6mm The collet is used to hold mini rotary accessories with a shank diameter of Ø 1.6mm....

Replacement collet - Ø 3.2mm The collet is used to hold mini rotary accessories with a shank diameter of Ø 3.2mm....

Multi chuck - Ø 0.8mm - 3.2mm The multi chuck is ideal for mini and micro drill bits, to secure hold different diameter accessories from Ø 0.8mm up to Ø 3.2mm....

Collet wrench The collet wrench is used to securely tighten the collet nut or multi chuck, locking the mini rotary accessory in place. The back end of the wrench has a flat tip screwdriver that can be used to change accessories on the mini rotary mandrels.....

Flexible shaft for TCMT001 rotary tool Collet diameter: Ø3.2mm Application: The collet is measured on the inside. There are three different collet sizes available. The collet size needs to correspond to the shaft diameter of the mini tool being used. A drill chuck (TCMT001DC) can also be used to substitute the use of a collet. TCMT001 accessories: TCMT001DC Drill chuck 0-3.2mm TCMT001FS Flexible shaft TCMT001SS Telescopic ha..

Flexible shaft for TCMT001 rotary tool Collet diameter: Ø2.3mm Application: The collet is measured on the inside. There are three different collet sizes available. The collet size needs to correspond to the shaft diameter of the mini tool being used. A drill chuck (TCMT001DC) can also be used to substitute the use of a collet. TCMT001 accessories: TCMT001DC Drill chuck 0-3.2mm TCMT001FS Flexible shaft TCMT001SS Telescopic ha..

Flexible shaft for TCMT001 rotary tool Collet diameter: Ø1.6mm Application: The collet is measured on the inside. There are three different collet sizes available. The collet size needs to correspond to the shaft diameter of the mini tool being used. A drill chuck (TCMT001DC) can also be used to substitute the use of a collet. TCMT001 accessories: TCMT001DC Drill chuck 0-3.2mm TCMT001FS Flexible shaft TCMT001SS Telescopic ha..

Chuck for TCMT001 rotary tool Application: The chuck is used to replace the collet clamping system of the TCMT001 rotary tool. The clamping range is Ø0.3-3.2mm. TCMT001 accessories: TCMT001DC Drill chuck 0-3.2mm TCMT001FS Flexible shaft TCMT001SS Telescopic hanging hook stand with desk clamp TCMT001-2-3-1 Collet with nut 3.2mm TCMT001-2-3-2 Collet with nut 2.3mm TCMT001-2-..

Collet set for thread 8 x 0.75 The collet set is used to hold the corresponding shank diameter. Collets included in the set: Ø 1.00mm Ø 1.50mm Ø 2.35mm Ø 3.00mm Ø 3.20mm Collet nut included for 8 x 0.75 thread....

Collet set for thread 9/32 x 40 The collet set is used to hold the corresponding shank diameter. Collets included in the set: Ø 0.80mm Ø 2.35mm Ø 3.00mm Ø 3.20mm Collet nut included for 9/32 x 40 thread....